Great Plains Logo

Select the Category


you would like to browse:


Home



1225
Replacement Lapheads are
sold each. For Eastern tool
only.
Laphead Pilot# Type Fits
16-0032 1 3/4" Motor 1958-up Big Twin
16-0026 1 1/2" Motor 40-54 Big Twin
16-0025 1 3/8" Motor 54-76 Sportster
55-57 Big Twin
29-73 45"
16-0018 1.562" Motor 87-up Sportster
16-0034 1.870" Trans. 36-77 Big Twin
16-0024 1.300" Trans. Sportster
16-0022 1 5/8" Rod Big Twin XL
16-0021 1 1/2" Rod 45"
1958-up Big Twin Case Lap Tool fea-
tures a lap which is supported on both
sides by a pilot on the bushing side &
plate which locates on the case pins of
the cam cover, by Jims. Order lap & pilot
VT No. 16-0881 for 1937-E77 4-spd main
race separately.
VT No. Item
16-1835 BT Case Lap Tool
16-0893 Case Lap Head only
16-0881 4-Speed Trans. Lap & Pilot
16-0892 4-Speed Lap Head only
Lapping Tools used for precision align-
ment of engine and transmission shafts.
Engine unit replaces 96710-40 to lap right
and left crankcase races for oversized
bearings. Transmission tool insures proper
fitting of oversized rollers with mainshaft
races on BT and Sportsters. The dual-pur-
pose “Combo Lap" for both engine and
transmission is also available. Rod laps
not included.
VT No. # Use Model Years
16-0135 C Motor Big Twin 1936-up
16-0119 B Trans. Big Twin 1936-77
XL
1952-83
16-0039 A Combo C & B As Above
16-0012 All Spanner Wrench
Rod Lapping
Tool includes
arbor assembly
1.500 lap for 45",
Indian, and some
case races, 1.625 lap for Big Twin,
Sportster and K Model rods.
VT No. Item
16-0027 Rod Tool
16-0012 Spanner Wrench
Trans. Lap Head
includes pilot. For
Eastern tool only.
VT No. Size Model
16-0020 1.870 BT 74 & 80
16-0019 1.300 1957-85 Sportster
Lap Head Pilots, sold each.
For Eastern tool only.
VT No. OEM
Type Years
16-1724 96727-56 Motor 55-up BT
16-1725 96728-56 Motor 54-76 XL
16-1726 96715-40 1½ Motor 30-54 BT
16-1727 96716-40 Motor 55-57 45",
BT
Motor 87-up XL
Lapping
Tools
A
B
C
Combo
Transmission
Motor
Rod Race Press Tool for easy installation
or extraction of rod races makes it easy to
support without bending rods for 74’s and
Sportsters.
VT No. Brand
16-0147 V-Twin
16-1838 Jims
Jims Timken Bearing Race Installer is
used to press race in straight in left crank
case for 1969-up BT,1977-up XL’s.
VT No. 16-0668
Sifton Flywheel
Washer Tool will
“stake" washers in
1971-up BT.
VT No. 16-1785
Shaft Turning Tool fits spline or taper on
assembled motor and allows engine to be
turned over by ½" ratchet or impact driver.
Sifton unless noted.
VT No. Years Type
16-0150 1930-54 Big Twin, Taper
16-1850* 1955-06 Big Twin, Spline
16-1378* 2006-up FXD, 07-up FL, FXST
16-1852 1957-up XL, Spline
*Note: Jims
1955-up Sprocket
Shaft Hard Cap
protects shaft
when using press.
By Jims.
VT No. 16-0666
1930-54 BT Flywheel
End Play Gauge .
VT No. 16-0131
Rod Clamping Tool
allows rod to be held
for straightening or to
replace wrist pin bush-
ing. 95952-33.
VT No. 16-0029